Resources · Construction Reference

Compression levels: what 8-15, 15-20, 20-30 and 30-40 mmHg actually mean

mmHg is a pressure, not a fabric weight — which is why two socks both labelled 20–30 mmHg can be built completely differently, and why the label alone tells you very little about what will arrive.

The short answer

  1. mmHg measures pressure at the ankle. It is set by spandex content, knit structure and size — not by how thick the sock feels.
  2. 8–15 travel and comfort · 15–20 everyday and travel recovery · 20–30 clinical-style support · 30–40 post-surgical territory.
  3. Graduated means pressure falls from ankle to calf — commonly 100% at the ankle, about 70% mid-calf, about 40% below the knee.
  4. Marketing a sock for a medical purpose crosses a regulatory line: in the EU that is a medical device under MDR, in the US it is FDA territory. "Support" and "medical" are not the same product.
  5. This catalogue carries 21 compression styles, and only 2 publish a mmHg band on the product page. That is the gap buyers hit first.

What the number measures

Compression is quoted in millimetres of mercury, measured at the ankle in a laboratory, on a specified test method, at a specified point on the leg. It is not a stretch rating and it is not a subjective firmness. A sock can feel tight and measure 12 mmHg, or feel moderate and measure 22 — because the measurement depends on how the fabric behaves on a leg of a given circumference, not on how it feels in the hand.

The bands below are the ones the trade actually uses. They are descriptive, not prescriptive; the clinical decision belongs to a clinician, and this page is about manufacturing.

The four commercial bands

What buyers in each band are normally building, and what to check before the order rather than after.

BandTypical useConstruction notesWhat to verify
8 – 15 mmHgTravel, flights, long sitting, everyday comfortLight graduated knit; 15–20% spandex; often fine gauge for a smooth legThat it is genuinely graduated, not uniform tube knit
15 – 20 mmHgEveryday support, travel recovery, standing occupations, sport recovery18–25% spandex; defined ankle-to-calf gradient; heel pocket matters for fitPressure at ankle and calf, and the size set it is graded for
20 – 30 mmHgClinical-style support, post-travel swelling, mild venous indicationHigher spandex, denser knit, often 200N fine gauge; sizing tolerance is narrowPressure test report per order, method and measurement points
30 – 40 mmHgPost-surgical and stronger clinical useMedical-device territory; requires a registered device and clinical evidenceRegulatory status first — this is not a normal OEM sock order

A sock labelled 20–30 mmHg in the wrong size does not deliver 20–30 mmHg. Sizing dominates the delivered pressure more than any other variable.

How graduated pressure is actually built

Uniform tightness is easy; graduated tightness is engineering. Four things produce the drop from ankle to calf:

  • Spandex content and denier. More spandex, or a coarser spandex, raises pressure. Most 20–30 mmHg constructions run 25–35% spandex by weight, against 3–8% in an ordinary sports sock.
  • Stitch density. A tighter knit per centimetre produces more pressure at the same circumference. This is why compression sits at 168N–200N rather than on a coarse machine.
  • Zoned knitting. The machine changes stitch length along the leg — tighter at the ankle, progressively looser toward the calf. A machine without this capability cannot make a graduated sock, whatever the yarn.
  • Size grading. Because pressure depends on circumference, the size set has to be built against the leg measurement it will be worn on, not against shoe size alone.

The measurement problem

"20–30 mmHg" is only meaningful with three pieces of information attached: the test method, the measurement points, and the tolerance.

  • Method. The two common laboratory methods are the Hatra tester and the MST/Swisslastic-type pressure tester. They do not give identical numbers on the same sock.
  • Points. Pressure is normally reported at the ankle (B), mid-calf (C) and below-knee (D), following a standard leg model. A single number hides the gradient.
  • Tolerance. A commercial tolerance of ±5 mmHg is normal in the band; a tighter tolerance costs more because more units are rejected at inspection.

A supplier who cannot state all three is quoting a marketing figure. A test report that states all three is a document you can put in front of a buyer.

Regulatory: the line you cannot market across

A sock that supports the leg is apparel. A sock marketed to treat or prevent a medical condition is a medical device, and the obligations change completely — device classification, technical file, clinical evaluation, labelling, and in the EU a notified-body route for the higher classes. The line is drawn by the claims, not by the pressure. Two identical socks, one sold as "support" and one sold as "reduces swelling", are in different regulatory categories.

For an OEM buyer this matters at the brief stage: decide which side of the line the product sits on before the packaging artwork is written, because the artwork is what regulators read.

What to check before placing a compression order

  1. Ask for a pressure test report on a production sample, not a development sample, stating method, points and tolerance.
  2. Confirm the size set is built on ankle and calf circumference, and that the grading matches the market you are selling into.
  3. Check the heel pocket. A compression sock without a shaped heel migrates down the leg and loses the ankle pressure that the whole product depends on.
  4. Confirm the laundering effect. Pressure decays with washing. Ask what the pressure is after 10 and after 25 domestic washes — that number is what the customer experiences.
  5. Agree the claim wording with the factory before artwork, so the label and the regulatory route agree.

Fabrication and weight context sits in yarn count and GSM; the construction side is in needle count and gauge. Our own compression range is at private label compression socks.

Compression level questions

What is the difference between 15-20 and 20-30 mmHg compression socks?

15–20 mmHg is everyday and travel support: enough to help with long sitting or standing, light enough to wear all day. 20–30 mmHg is a clinical-style band with a firmer ankle gradient, used where a stronger, more defined pressure profile is wanted. The construction differs — more spandex, denser knit, narrower sizing tolerance — and so does the price.

Is 20-30 mmHg a medical device?

It depends on the claim, not the pressure. If the product is marketed to treat or prevent a medical condition, it is regulated as a medical device in most markets. Sold as support hosiery without medical claims, the same construction is apparel. The claim wording on the packaging is what regulators assess.

How is compression measured?

On a laboratory leg model, at defined points — normally ankle, mid-calf and below-knee — using a Hatra or MST-type pressure tester. A meaningful report states the method, the measurement points and the tolerance; a single mmHg figure without those is not checkable.

Does compression wash out?

It decays. Elastane fatigues with washing and heat, so delivered pressure falls over the life of the sock. Ask for pressure after 10 and after 25 domestic washes at the specified temperature — that is the number the end customer experiences, not the number on the box.

Can you make 20-30 mmHg socks with our branding?

Yes, as apparel-grade support hosiery with branded packaging. If your product carries medical claims, the device registration and clinical documentation sit with the brand owner in your market, and we will supply the production and test documentation that route requires. We publish process documentation, not device certifications of our own.

Tell us the band and the market.

mmHg band, size set and claim wording determine the construction. Send all three and the quotation will be accurate the first time.